om02screenparameters0470
| Message | Description | Required operation |
|---|---|---|
| ** library will be overwritten. | The Library file with the same name has already been loaded when you tried to load a library. The existing data will be overwritten when the new data is loaded. The name of the Library file you are attempting to load is displayed in place of **. | |
| ** Control Assign full. | Could not carry out the operation because there is no controller set available. The Part name you are attempting to add to the controller set is displayed in place of “**.” | Delete the unnecessary controller set and redo the operation. |
| ** will be deleted. | Data will be deleted as a result of this operation. | |
| ** will be loaded to Pattern. | The .mid file will be loaded to the Pattern. | |
| ** will be loaded to Song. | The .mid file will be loaded to the Song. | |
| ** will be loaded. | The file will be loaded. | |
| ** will be overwritten. | When saving, the Performance, file, folder, or Quick Setup with the same name already exists. The existing data will be overwritten when saved. The name of the Performance, file, folder, or Quick Setup that you are attempting to save is displayed in place of “**.” | |
| Activate the source controller to assign. | You can assign parameters to the controller you are about to operate. | Operate the controller that you wish to assign. |
| Advanced settings will be initialized. | Initializes the settings of the [UTILITY] → Settings → Advanced tab. | |
| All data and libraries will be initialized. Unsaved user data will be lost. | Restores the factory default settings. | It is recommended to save any necessary settings you wish to keep to a USB flash drive in advance. |
| All data is initialized upon power-on. | The instrument has been set to restore factory defaults when the instrument is turned on. | |
| All data will be overwritten by ** | When loading is performed, all data will be overwritten. The name of the backup file you are attempting to load is displayed in place of “**.” | |
| All Favorite Marks will be cleared. | All Favorite marks will be deleted. | |
| All settings will be initialized. User data is kept. | The settings for the instrument will be initialized. The User data will not be deleted. | |
| All sound will be stopped during optimization. | The internal memory will be restored. | |
| All user data will be initialized. Unsaved user data will be lost. | The User area in the User memory will be initialized. It is recommended to save any necessary settings you wish to keep to a USB flash drive in advance. | |
| Arpeggio bypass disabled. | The Arpeggio Bypass has been deleted. | |
| Arpeggio full. | Could not carry out the operation because the Arpeggio is full. | |
| Assignable knob full. | Could not carry out the operation because all assignable knobs are used in the controller set. | Delete any unnecessary controller set that has an assignable knob set as a Source and redo the operation. |
| Audio file is not found. | The specified audio file cannot be found. | |
| Audio Rec stopped due to lack of memory space. | Audio recording stopped automatically because the USB flash drive is full. | Use a new USB flash drive or delete unnecessary files and try this operation again. |
| Audition full. | Could not carry out the operation because the User Audition data is full. | Delete unnecessary User Audition data from: [UTILITY] → Contents → Data Utility screen. |
| Auto power off disabled. | The Auto Power Off function has been disabled. | |
| Bulk data protected. | Bulk data cannot be received because of the setting. | |
| Can’t process. | Cannot process the requested operation. | |
| Can’t register unstored performance. | Cannot register the Performance to the Live Set because the bank or program number being edited has not yet been set. | |
| Completed. | The specified load, save, format, or other Job has been completed. | |
| Connecting to USB device... | Connecting the USB flash drive to the instrument. | |
| Converting Pattern to Song. | The Pattern is being converted. | |
| CPU Fan Error | The built-in cooling fan has stopped. | This condition may cause the internal temperature to rise and the instrument may stop working. Immediately back up all necessary data, turn off the instrument and contact your Yamaha dealer. |
| Current user data will be overwritten by **. | User data already exists at the destination for the file to be loaded. If you proceed, the existing user data will be overwritten. The name of the User file you are attempting to load is displayed in place of “**.” | |
| Curve full | Could not carry out the operation because the User Curve data is full. | Delete unnecessary User Curve data from: [UTILITY] → Contents → Data Utility screen. |
| Data memory full. | (When loading a Library file) The content data in the library cannot be saved because the instrument memory is full. | |
| Device number is off. | The bulk data cannot be sent or received because the device number is off. | |
| Device number mismatch. | The bulk data cannot be sent or received because the device number does not match. | |
| Dividing the drum track makes new performance data. Performance full. | Cannot carry out the operation because there is no Performance available for using Divide Drum Track. | |
| Dividing the drum track makes new performance data. You can’t undo this operation. | A new Performance will be created by using Divide Drum Track. This operation cannot be undone. | |
| File is not found. | There are no files for the selected type. | |
| File or folder already exists. | A file or folder with the same already exists. | |
| File or folder path is too long. | Cannot open the specified file or folder because its path name is too long. | |
| Folder is not empty. | You are attempting to delete a folder that contains data. | |
| Folder is too deep. | Cannot open the folder because it is nested too deep in the folder structure. | |
| Illegal bulk data. | An error occurred while receiving bulk data or bulk requests. | |
| Illegal file name. | The file name is invalid. | |
| Illegal file. | The specified file cannot be handled or loaded into this instrument. | |
| Illegal parameters. | Incorrect parameters have been specified. | |
| Illegal sample data. | The specified sample data is not supported. | |
| Illegal smart morph data. | The specified Smart Morph data is not supported. | |
| Keybank full. | While loading, the total number of keybanks exceeds the maximum number. | |
| Keyboard control lock disabled. | The Keyboard Lock has been disabled. | |
| Knob value stored. | The Knob Value has been stored (saved). | |
| Library full. | The total number of libraries exceeds the maximum number. | |
| Micro Tuning full | Could not be loaded because the User Micro Tuning data is full. | Delete unnecessary User Micro Tuning data from: [UTILITY] → Contents → Data Utility screen. |
| MIDI buffer full. | Could not be processed because an excessively large amount of MIDI data was received at once. | |
| MIDI checksum error. | The checksum of the received System Exclusive message is incorrect. | |
| No data. | There is no data in the selected track or specified range. Select the range again. | |
| No read/write authority to the file. | No read or write permissions for this file. | |
| Note ranges will be initialized. | The Note Range will be initialized. | |
| Now initializing all data… | The factory settings are being restored. | |
| Now initializing… | Some data is being initialized. | |
| Now loading... | The file is being loaded. | |
| Now receiving MIDI bulk data... | The instrument is receiving MIDI bulk data. | |
| Now saving... | The file is being saved. | |
| Now transmitting MIDI bulk data... | The instrument is sending MIDI bulk data. | |
| Panel unlocked. | The panel lock has been disabled. | |
| Part *** will be overwritten. | There is already a Part at the copy destination. If you continue the operation, the existing Part at the copy destination will be overwritten. | |
| Part full. | Could not open the Rhythm Pattern screen because there were no Parts available. | Delete the unnecessary Part(s) and redo the operation. |
| Pattern full. | Could not carry out the operation because the Pattern is full. | |
| Pattern will be converted to Song. | The Pattern will be converted to a Song. | |
| Performance data in *** will be loaded. | The Performance Data in the file for a past model will be loaded. | |
| Performance full. | Could not carry out the operation because the Performance is full. | |
| Please connect USB device. | Connect a USB flash drive. | |
| Please keep power on. | Writing data in the flash ROM. | Do not turn off the instrument while this message is shown. If the instrument is turned off while this is displayed, User data may be lost or the system may be corrupted, preventing the system from starting properly the next time the instrument is turned on. |
| Please reboot to enable the new Audio I/O Mode. | Restart the instrument to enable the changes to the audio input and output settings. | |
| Please reboot to enable the new USB Driver Mode. | Restart the instrument to enable the changes to the USB driver mode settings. | |
| Please reboot to maintain internal memory. | Restart the instrument to repair the instrument memory. | |
| Please stop audio play/rec. | Stop audio recording or playback, and then try again. | |
| Please stop sequencer. | Stop the sequencer (Pattern or Song), and then try again. | |
| Please store the pattern to change the chain play mode. | Store the Pattern before changing the chain playback mode. | |
| Please wait… | Processing. | Please wait. |
| Press [SHIFT] + [TEMPO/TAP] to unlock panel. | Panel Lock has been enabled. Press [SHIFT] + [TEMPO/TAP] to unlock the panel. | |
| Quick Setup ** is loaded. | Quick Setup has been loaded. | |
| Recall latest edits. | Recalls the last edited Performance data and puts it in the edit buffer. | |
| Redo **. | Carries out the operation again (Redo) that had been undone. The name of the operation is displayed in place of “**.” | |
| Sample is protected. | The sample is protected and cannot be changed. | |
| Sample is too long. | The sample size is too large and cannot be loaded. | |
| Sample is too short. | The sample size is too small and cannot be loaded. | |
| Sample memory full. | The memory for samples is full and cannot be loaded. | |
| Scene stored. | The Scene has been stored (saved) to the SCENE button. | |
| Selected items will be copied to user bank. | The Performance will be copied to the User Bank. | |
| Smart Morph full. | The total number of Performances with Smart Morph exceeds the maximum number. | |
| Some keybanks were not loaded. | Some key banks are in the old format and cannot be loaded. | |
| Song/Pattern data overload. | The Song or Pattern cannot be played back because it is overloaded. | |
| Song full. | The total number of Songs exceeds the maximum number. | |
| SSS disabled. | SSS has been disabled. | |
| SSS enabled. | SSS has been enabled. | |
| Touch the white square. | (During touch panel calibration) Tap the white square that appears on the display. | |
| Turn on Memory Switch to memorize ** into this scene. | To register a function to a Scene, Memory (Memory Switch) for the function must be turned on in advance. | Turn on the switch from: [PERFORMANCE] → Scene. |
| Undo **. | Cancels the last action (Undo). The name of the operation is displayed in place of “**.” | |
| Unsupported USB device. | This USB device is not supported by this instrument. | |
| USB connection terminated. | The USB flash drive was shut off due to abnormal current flow. | Disconnect the USB flash drive and then press any button on the top panel. |
| USB device is full. | The USB flash drive is full and files cannot be saved. | Use a new USB flash drive or delete unnecessary files, and try this operation again. |
| USB device is write-protected. | The USB flash drive you are using is write-protected. | |
| USB device read/write error. | An error occurred during read/write to the USB flash drive. | |
| USB device will be formatted. | The USB flash drive will be formatted. | |
| User auditions will be overwritten with stored songs. | The existing User Audition will be overwritten by the currently stored Song. | |
| VCM Rotary is disabled except in Part 1. | The VCM Rotary can be used only with Part 1. It cannot be used on other Parts. | |
| Voice data in *** will be loaded. | The Voice Data in a file for a previous model is loaded. | |
| Waveform full. | The total number of waveforms exceeds the maximum number. |
Print this page