VXL1 Series Online Owner's Manual

  • About this manual
  • Installing the speaker
    • Pre-installation
    • Installation with included brackets (excluding -WR [outdoor model])
    • Installation with wall mounting bracket (WMB-L1)(excluding -WR [outdoor model])
    • Installation by vertical coupling (VCB-L1 + WMB-L1 + VCSB-L1) (excluding -WR [outdoor model])
    • Installation by horizontal coupling (HCB-L1 + WMB-L1) (excluding -WR [outdoor model])
    • Installation with pole and wall mount bracket (PWMB-L1-WR [for outdoor model])
      • Wall mount with Arm
      • Wall mount without Arm
      • Pole mount with Arm
      • Pole mount without Arm
  • Installing the speaker transformer (ST-L1a)
  • Installing the port cover (excluding -WR [outdoor model])
  • Painting
  • HOME
  • About this manual

About this manual

This product is a fixed-installation speaker system used for amplifying sound and background music, in commercial spaces and similar areas.
The VXL1 comprises the following models:
“-WR” represents an outdoor model. In this manual, outdoor models are referred to as “-WR”.

  • VXL1(B/W)-24, VXL1(B/W)-24-WR with 24-speaker unit
  • VXL1(B/W)-16, VXL1(B/W)-16-WR with 16-speaker unit
  • VXL1(B/W)-8, VXL1(B/W)-8-WR with 8-speaker unit
This manual explains to the installer how to install the product.

Caution for safe installation is stated in “Installation Guide” which is included with the product. Please read this manual thoroughly before use.

Meaning of warning display

The following notation is used in this manual.

Please read this manual and make sure you understand the meaning of the display.

WARNING
This display indicates “It may result in death or serious injury”.
CAUTION
This display indicates “It may result in physical injury”.

The following symbol is indicated the caution.

NOTICE
This display indicates “It may result in property damage”.
NOTE
This information is provided to increase understanding or make operation easier.

  • The illustrations as shown in this manual are for instructional purposes only.
  • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
  • Communication charges may result when connecting to (accessing) the site.
  • This manual may not be available depending on the network or communication environment.
  • Google Analytics

© 2024 Yamaha Corporation
Published 02/2025 CR-C0


HOME

  • HOME
  • Installing the speaker

Installing the speaker

  • Pre-installation
  • Installation with included brackets (excluding -WR [outdoor model])
  • Installation with wall mounting bracket (WMB-L1)(excluding -WR [outdoor model])
  • Installation by vertical coupling (VCB-L1 + WMB-L1 + VCSB-L1) (excluding -WR [outdoor model])
  • Installation by horizontal coupling (HCB-L1 + WMB-L1) (excluding -WR [outdoor model])
  • Installation with pole and wall mount bracket (PWMB-L1-WR [for outdoor model])

HOME

  • HOME
  • Installing the speaker
  • Pre-installation

Pre-installation

Strip the cable insulation as shown in the figure and connect the cables.

NOTE
Do not use solder to plate stranded wires, as this may cause the wires to break.

HOME

  • HOME
  • Installing the speaker
  • Installation with included brackets (excluding -WR [outdoor model])

Installation with included brackets (excluding -WR [outdoor model])

You can use the included mounting bracket to install the speaker on a wall.
Before installation, make sure the installation area can support the weight of the speaker.
Do not install on plasterboard.

NOTICE
When installing speakers, make sure the power amplifier is turned off.
CAUTION
Do not install the speakers horizontally, as the speakers may fall.
NOTE
This speaker can be painted with acrylic lacquer. See “Painting” for details.

Attaching the bracket base to the wall

  1. Place the included template on the wall, to decide where the holes should go for the screws and cables.
  2. Make holes in the wall for the cables, and pull the cables from the amplifier out through the holes.
  3. Install the bracket base onto the wall. Position the narrow part of the bracket base down (towards the floor).
    The bracket base holes should be φ5.3 mm in size.

Installing the mounting bracket and safety wire onto the speakers

  1. Install the mounting bracket onto the speaker using the included screws.
    Position both the upper and lower part of the mounting bracket at the third hole to install (see the figure below; only VXL1-8 have one location).
    Install the safety wire at the topmost hole position.
    CAUTION
    • Use the included safety wire.
    • If the included safety wire is not long enough, consider the weight of the speaker and the installation conditions, and procure an appropriate safety wire.

Setting the directionality (VXL1-24, VXL1-16 only)

  1. Set the directionality by using a flat head screwdriver to operate the Vertical Coverage Selector on the back of the speaker.

    At this time, when you want to expand the area of coverage downwards, set the switch to WIDE.

Connecting the cables

  1. Remove the Euroblock plug from the speaker.
    NOTE
    Although there are two different speaker connectors for top and bottom, they are the same (connected in parallel internally). You can use either one.
  2. After loosening the terminal screws of the Euroblock plug with a flat-blade screwdriver, insert the cable into each terminal and tighten the screws.
    Tug on the cables to make sure that they cannot be pulled out.
    NOTE
    When installing outdoors, run the cables through the included terminal cover before inserting them into the connector.
    NOTE
    Use a flat-headed screwdriver with a blade width of 3 mm or less.
  3. Attach the safety wire to the wall.
    CAUTION
    Attach the safety wire at a position higher than the speaker, where it does not sag.
  4. Bring the connected Euroblock plug back to the socket on the main unit.

    When installing outdoors, attach the included terminal cover.
    NOTE
    Take appropriate measures to waterproof the openings below the terminal covers.

Installing the main speaker unit onto the wall

  1. Fit the bracket base together with the mounting bracket by inserting from the top, making sure to insert the mounting bracket all the way until the parts lock together.

    NOTICE
    • Hold the middle of the speaker when installing.
    • (For VXL1-24, VXL1-16 only) Make sure that the mounting base and mounting bracket are locked together in two places, top and bottom.

    When removing, pick up the speaker while lightly pushing to the left.


HOME

  • HOME
  • Installing the speaker
  • Installation with wall mounting bracket (WMB-L1)(excluding -WR [outdoor model])

Installation with wall mounting bracket (WMB-L1)(excluding -WR [outdoor model])

CAUTION
  • Do not install the wall mounting bracket WMB-L1 onto any speaker system other than the VXL1 Series.
  • When coupling the speaker vertically with the VCB-L1, make sure to use the VCSB-L1.
  • Do not use the wall mount bracket WMB-L1 outdoors.
  • Use the pole and wall mount bracket PWMB-L1-WR to mount the VXL1-WR (outdoor models).

When using it together with the vertical coupling support bracket VCSB-L1, see "Installation by vertical coupling (VCB-L1 + WMB-L1 + VCSB-L1) (excluding -WR [outdoor model]).”

Attaching the bracket base to the wall

  1. Remove the attached screw from the bracket in advance.
  2. Place the included template on the wall, to decide where the holes should go for the bracket base.
  3. Install the bracket base onto the wall. The bracket base holes should be φ12 mm in size.

Installing the mounting bracket and safety wire onto the speakers

  1. Install the mounting bracket onto the speaker using the included screws.
  2. Attach the safety wire. See the figure below for the locations of the mounting bracket and the safety wire.

Connecting the cables

  1. Remove the Euroblock plug from the speaker.
  2. After loosening the terminal screws of the Euroblock plug with a flat-blade screwdriver, insert the cable into each terminal and tighten the screws.
    Tug on the cables to make sure that they cannot be pulled out.
    NOTE
    When installing outdoors, run the cables through the included terminal cover before inserting them into the connector.
    NOTE
    Use a flat-headed screwdriver with a blade width of 3 mm or less.
  3. Attach the safety wire to the wall.
    CAUTION
    Attach the safety wire at a position higher than the speaker, where it does not sag.
  4. Bring the connected Euroblock plug back to the socket on the main unit.

Installing the main speaker unit onto the wall

  1. Fit the bracket base together with the mounting bracket by inserting from the top.
  2. Temporarily fasten the speaker using the removed angle-adjusting bolt.
  3. Set a vertical swing angle. Fasten the two bolts (tightening torque: upper about 6.0 N·m, lower about 2.0 N·m) with the included hex wrench.
    NOTE
    Guides are inscribed on the bracket base in 2° increments.
  4. Adjust a horizontal swing angle, and fasten the screw of the bracket base (tightening torque: about 12.0 N·m).

HOME

  • HOME
  • Installing the speaker
  • Installation by vertical coupling (VCB-L1 + WMB-L1 + VCSB-L1) (excluding -WR [outdoor model])

Installation by vertical coupling (VCB-L1 + WMB-L1 + VCSB-L1) (excluding -WR [outdoor model])

CAUTION
  • Do not install the vertical coupling support bracket VCSB-L1 onto any speaker system other than the VXL1 Series.
  • When coupling the speaker vertically with the VCB-L1 and installing it with the WMB-L1, make sure to use the VCSB-L1.
  • Do not use the vertical coupling bracket VCB-L1 or vertical coupling support bracket VCSB-L1 outdoors.
NOTE
Screws for installing the bracket base onto the wall should be procured according to the wall material and structure.

Installing the vertical coupling bracket (VCB-L1) onto the speaker

  1. Install the vertical coupling bracket onto the speaker using the included screws.

Connecting the cable between the vertically coupled speakers

  1. Remove the Euroblock plug from the speaker.
    NOTE
    Although there are two different speaker connectors for top and bottom, they are the same (connected in parallel internally). You can use either one.
  2. Use a flat-headed screwdriver to loosen the terminal screws of the Euroblock plug, insert the cables into the terminal openings, and then tighten the screws.
    Make sure the cables are secure and cannot be pulled out.
    NOTE
    When installing outdoors, run the cables through the included terminal cover before inserting them into the connector.
    NOTE
    Use a flat-headed screwdriver with a blade width of 3 mm or less.
  3. Connect the coupled speaker connectors to each other.

Attaching the bracket base to the wall

  1. Place the included template on the wall, to decide where the holes should go for the bracket base.
    The distance from the slotted hole in the top of bracket base for VCSB-L1 to the hole in the bottom of bracket base for WMB-L1 is as shown in the figure.
  2. Install the bracket base for VCSB-L1 onto the wall. The size of the slotted hole is 12 × 17 mm.
  3. Install the bracket base for WMB-L1 onto the wall. The bracket base holes should be φ12 mm in size.

Installing the mounting bracket and safety wire onto the speakers

  1. Remove the attached screw from the bracket in advance.
  2. Attach the included safety wire to the speaker.
  3. Install the mounting bracket VCSB-L1 in the second hole from the speaker top using the included screw.
  4. Install the mounting bracket WMB-L1 in the fourth and fifth holes from the speaker bottom.

Connecting the cables between the amplifier and the speaker unit

  1. Attach the safety wire to the wall.
    CAUTION
    Attach the safety wire at a position higher than the speaker, where it does not sag.
  2. Connect the cables from the amplifier to the speaker connector of the speaker unit.

Installing the main speaker unit onto the wall

  1. Fit the bracket base for WMB-L1 together with the mounting bracket by inserting from the top.
  2. Align the mounting bracket with the bracket base for VCSB-L1, and give temporary tightening to the point (A) using the removed screw.
  3. Following the desired vertical swing angle, insert a spacer into the bracket and fasten it using the included wing nut.
    See "Installation pattern" for the angle.
  4. Give final tightening to the temporarily tightened screw (tightening torque: about 0.6 N·m).
  5. Fasten the two bolts of WMB-L1 (tightening torque: upper about 6.0 N·m, lower about 2.0 N·m) with the included hex wrench.
  6. Set a horizontal swing angle. Following the swing angle, give final tightening to the screws on the bracket base (tightening torque: about 12.0 N·m).

HOME

  • HOME
  • Installing the speaker
  • Installation by horizontal coupling (HCB-L1 + WMB-L1) (excluding -WR [outdoor model])

Installation by horizontal coupling (HCB-L1 + WMB-L1) (excluding -WR [outdoor model])

CAUTION
  • Do not install the horizontal coupling bracket HCB-L1 onto any speaker system other than the VXL1 Series.
  • Do not use the horizontal coupling bracket HCB-L1 outdoors.

Installing the horizontal coupling bracket onto the speaker

  1. Install the bracket onto the speaker using the included screws.
    For VXL1-24 and VXL1-16, install the horizontal coupling bracket (S) in the first hole from the top, and the horizontal coupling bracket (L) in the fourth and fifth holes from the top.

    For VXL1-8, install the horizontal connecting bracket (L) in the first and second holes from the top, and the horizontal connecting bracket (S) in the first hole from the bottom.

Installing the main speaker unit onto the wall

  1. Install the unit onto the wall using the WMB-L1.
    See "Installation with wall mounting bracket (WMB-L1)(excluding -WR [outdoor model])" for the installation procedure.

HOME

  • HOME
  • Installing the speaker
  • Installation with pole and wall mount bracket (PWMB-L1-WR [for outdoor model])

Installation with pole and wall mount bracket (PWMB-L1-WR [for outdoor model])

  • Wall mount with Arm
  • Wall mount without Arm
  • Pole mount with Arm
  • Pole mount without Arm

Be sure to read the following before installation

Caution for safe installation is stated in “Read Me First” which is included with the product. Please read this manual thoroughly before use.
This product package does not include any screws, bolts, belts, etc. that could be used to install the bracket on a pole or wall. If you plan for such an installation, prepare the necessary metal fittings separately.

WARNING
  • If installing a VXL1-WR (outdoor model), be sure to use a PWMB-L1-WR pole and wall mounting bracket.
  • Choose a location that can sufficiently support the total weight of this product plus a compatible speaker.
  • Tighten bolts and screws to the recommended torque levels.
  • Be sure to use safety wires to prevent the speaker from falling.
  • Perform regular maintenance and inspection once a year.
CAUTION
Wear thick work gloves during installation.
NOTICE
For unused speaker terminals, fasten the terminal cover with screws and implement appropriate measures to ensure the opening at the bottom of the terminal cover is waterproof.
Yamaha cannot be held responsible for damage or injury caused by insufficient strength of the support structure or improper installation.

HOME

  • HOME
  • Installing the speaker
  • Installation with pole and wall mount bracket (PWMB-L1-WR [for outdoor model])
  • Wall mount with Arm

Wall mount with Arm

Attaching the mounting bracket and safety wire to a speaker

  1. Attach the mounting bracket to the speaker using the included screws Ⓓ.
    Attach one bracket for model VXL1-8-WR or two brackets for models VXL1-16-WR and VXL1-24-WR.
    Refer to the figure below to determine where to attach the mounting bracket and safety wire.


    NOTICE
    Check the mounting bracket top/bottom orientation.
    Orient the bracket with the guide on top.
    WARNING
    • Use the included safety wire.
    • If the included safety wire is not long enough, procure a suitable safety wire that is long enough and strong enough for the speaker weight and installation conditions.
  2. Attach the bracket base to the arm unit using the included bolt Ⓐ.
    With the bracket oriented straight out, tighten the bolt until it stops moving.

    NOTICE
    Check bracket base top/bottom orientation.
    Orient the side with the marking toward the top.

Mounting the speaker unit to a wall

  1. Place the included template against the wall to position the holes for attaching the bracket base.

  2. Drill a hole in the wall for routing the wires and then pull out the wires from the amplifier.


  3. Attach the safety wire to the wall.

    WARNING
    Attach the safety wire at a position higher than the speaker with no slack.
  4. Fasten the bracket base to the wall.
    Rotate the bracket base toward the side so the base can be attached to the wall.
    The dimensions of the upper elongated hole are 13 × 15 mm. The middle and lower elongated holes are 13 × 20 mm.


Connecting the wires

  1. Disconnect the Euroblock plug from the speaker unit.
    NOTE
    Although there are two different speaker connectors, at the top and bottom, they have the same function (connected in parallel internally). Either one may be used.
  2. Use a flat-head screwdriver to loosen the terminal screws in the Euroblock plug, insert the wires into the terminal openings, and then securely fasten the screws.
    Pull on the wires to confirm they cannot be pulled out.
    NOTE
    Route the wires through the included terminal cover before inserting them into the connector.
    NOTE
    Use a flat-head screwdriver with a blade width of 3 mm or less.
  3. After connecting the wires, reinsert the Euroblock plug back into the socket on the main unit.
    Fasten the terminal cover to the main unit with screws.



    NOTICE
    Implement appropriate measures to ensure the opening at the bottom of the terminal cover is waterproof.

Setting the speaker orientation (VXL1-24-WR, VXL1-16-WR only)

  1. Use a flat-head screwdriver to set the vertical coverage selector switch located on the back of the speaker.



    To expand the downward coverage area, set the switch to the [WIDE] position.



Adjusting the speaker angle

  1. The vertical angle can be adjusted within the 0° to 10° range for models VXL1-8-WR and VXL1-16-WR or the 0° to 4.5° range for model VXL1-24-WR. The angle guide markings stamped into brackets are shown below.


    VXL1-8-WR
    Mount the speaker with the sliding arm of the mounting bracket in its fully retracted (shortest) position.




    VXL1-16-WR




    VXL1-24-WR




  2. Align the marking to the desired vertical angle position and tighten the included bolt Ⓐ.

  3. Adjust the horizontal swing angle and then tighten the bolts on the top and bottom of the bracket base.




HOME

  • HOME
  • Installing the speaker
  • Installation with pole and wall mount bracket (PWMB-L1-WR [for outdoor model])
  • Wall mount without Arm

Wall mount without Arm

Disassembling the mounting bracket

  1. Remove the attached bolts from the bracket in advance.
    Use a 13 mm wrench for the M8 bolt and a 10 mm wrench for the M6 bolts.


    NOTICE
    • When installing mounting bracket Ⓐ onto the speaker, use the removed washers (for square neck bolts) in combination with the included bolts Ⓒ (M6 × 25). Refer to Attaching the mounting bracket and safety wire to the speakers.
    • If mounting the speaker to a wall, reuse the removed flat and spring washers and nuts. Refer to Mounting the speaker unit to a wall.

Disassembling the bracket base

  1. Remove the previously attached bolts from the base.


Attaching the bracket base to a wall

  1. Hold the template against the wall to determine hole positions for attaching bracket base Ⓐ.

  2. Drill a hole in the wall for routing the wires and then pull out the wires from the amplifier.


  3. Attach the bracket base to the wall.
    Rotate the bracket base toward the side so the base can be attached to the wall.
    The dimensions of the upper elongated hole are 13 × 15 mm. The middle and lower elongated holes are 13 × 20 mm.


Connecting the wires

  1. Disconnect the Euroblock plug from the speaker unit.
    NOTE
    Although there are two different speaker connectors, at the top and bottom, they have the same function (connected in parallel internally). Either one may be used.
    However, to use the upper connector, attach the wires and fasten the terminal cover to the speaker unit with screws before attaching the disassembled bracket base Ⓐ.
  2. Use a flat-head screwdriver to loosen the terminal screws in the Euroblock plug, insert the wires into the terminal openings, and then securely fasten the screws.
    Pull on the wires to confirm they cannot be pulled out.
    NOTE
    Route the wires through the included terminal cover before inserting them into the connector.
    NOTE
    Use a flat-head screwdriver with a blade width of 3 mm or less.
    Reconnect the Euroblock plug, with the wires attached, back into the socket on the main unit after the speaker is attached to the wall.
  3. Attach the safety wire to the wall.
    WARNING
    • Use the included safety wire.
    • If the included safety wire is not long enough, procure a suitable safety wire that is long enough and strong enough for the speaker weight and installation conditions.
    • Attach the safety wire at a position higher than the speaker with no slack.

Attaching the mounting bracket and safety wire to a speaker

  1. Install bolts Ⓒ (M6 × 25 square neck bolts, washers, and nuts) included with mounting bracket Ⓐ.
    Use the washers (M6 for square neck bolts) removed during mounting bracket disassembly.


  2. Use the included screws Ⓓ to attach mounting bracket Ⓐ (with included M6 × 25 square neck bolts) to the speaker.
    Attach one bracket for model VXL1-8-WR or two brackets for models VXL1-16-WR and VXL1-24-WR.
    Refer to the figure below to determine the location for attaching mounting bracket Ⓐ and the safety wire.



Setting the speaker orientation (VXL1-24-WR, VXL1-16-WR only)

  1. Use a flat-head screwdriver to set the vertical coverage selector switch located on the back of the speaker.

    To expand the downward coverage area, set the switch to the [WIDE] position.

Mounting the speaker unit to a wall

  1. Install it to the second and third holes from the top of bracket base Ⓐ.
    Rotate bracket base Ⓐ toward the side so the base can be attached.

  2. Install the speaker using the flat washers, spring washers, and nuts obtained from disassembling the mounting bracket.


  3. After connecting the wires, reinsert the Euroblock plug back into the socket on the main unit.
    Fasten the terminal cover to the main unit with screws.



    NOTICE
    Implement appropriate measures to ensure the opening at the bottom of the terminal cover is waterproof.

Adjusting the speaker angle

  1. Adjust the horizontal swing angle and then tighten the bolts on the top and bottom of the bracket base.




HOME

  • HOME
  • Installing the speaker
  • Installation with pole and wall mount bracket (PWMB-L1-WR [for outdoor model])
  • Pole mount with Arm

Pole mount with Arm

Attaching the mounting bracket and safety wire to a speaker

  1. Attach the pole base to the bracket base using the included screws Ⓑ.


  2. Attach the mounting bracket to the speaker using the included screws Ⓓ.
    Attach one bracket for model VXL1-8-WR or two brackets for models VXL1-16-WR and VXL1-24-WR.
    Refer to the figure below to determine where to attach the mounting bracket and safety wire.


    NOTICE
    Check the mounting bracket top/bottom orientation.
    Orient the bracket with the guide on top.
    WARNING
    • Use the included safety wire.
    • If the included safety wire is not long enough, procure a suitable safety wire that is long enough and strong enough for the speaker weight and installation conditions.
  3. Attach the bracket base to the arm unit using the included bolt Ⓐ.
    With the bracket oriented straight out, tighten the bolt until it stops moving.


    NOTICE
    Check bracket base top/bottom orientation.
    Orient the side with the marking toward the top.

Mounting the speaker to a pole

  1. Attach the safety wire in a manner that allows confirming its ability to prevent the speaker from falling.
  2. Insert two stainless steel bands through the elongated holes in the bracket base and fasten them to the pole.


Connecting the wires

  1. Disconnect the Euroblock plug from the speaker unit.
    NOTE
    Although there are two different speaker connectors, at the top and bottom, they have the same function (connected in parallel internally). Either one may be used.
  2. Use a flat-head screwdriver to loosen the terminal screws in the Euroblock plug, insert the wires into the terminal openings, and then securely fasten the screws.
    Pull on the wires to confirm they cannot be pulled out.
    NOTE
    Route the wires through the included terminal cover before inserting them into the connector.
    NOTE
    Use a flat-head screwdriver with a blade width of 3 mm or less.
  3. After connecting the wires, reinsert the Euroblock plug back into the socket on the main unit.
    Fasten the terminal cover to the main unit with screws.



    NOTICE
    Implement appropriate measures to ensure the opening at the bottom of the terminal cover is waterproof.

Setting the speaker orientation (VXL1-24-WR, VXL1-16-WR only)

  1. Use a flat-head screwdriver to set the vertical coverage selector switch located on the back of the speaker.



    To expand the downward coverage area, set the switch to the [WIDE] position.



Adjusting the speaker angle

  1. The vertical angle can be adjusted within the 0° to 10° range for models VXL1-8-WR and VXL1-16-WR or the 0° to 4.5° range for model VXL1-24-WR. The angle guide markings stamped into brackets are shown below.


    VXL1-8-WR
    Mount the speaker with the sliding arm of the mounting bracket in its fully retracted (shortest) position.




    VXL1-16-WR




    VXL1-24-WR




  2. Align the marking to the desired vertical angle position and tighten the included bolt Ⓐ.

  3. Adjust the horizontal swing angle and then tighten the bolts on the top and bottom of the bracket base.




HOME

  • HOME
  • Installing the speaker
  • Installation with pole and wall mount bracket (PWMB-L1-WR [for outdoor model])
  • Pole mount without Arm

Pole mount without Arm

Disassembling the mounting bracket

  1. Remove the attached bolts from the bracket in advance.
    Use a 13 mm wrench for the M8 bolt and a 10 mm wrench for the M6 bolts.


    NOTICE
    • When installing mounting bracket Ⓐ onto the speaker, use the removed washers (for square neck bolts) in combination with the included bolts Ⓒ (M6 × 25). Refer to Attaching the mounting bracket and safety wire to the speakers.
    • If mounting the speaker to a wall, reuse the removed flat and spring washers and nuts. Refer to Mounting the speaker unit to a pole.

Disassembling the bracket base

  1. Remove the previously attached bolts from the base.


Attaching the bracket base to a pole

  1. Attach the pole base to bracket base Ⓐ using the included screws Ⓑ.


  2. Insert two stainless steel bands through the elongated holes in bracket base Ⓐ and fasten them to the pole.


Connecting the wires

  1. Disconnect the Euroblock plug from the speaker unit.
    NOTE
    Although there are two different speaker connectors, at the top and bottom, they have the same function (connected in parallel internally). Either one may be used.
    However, to use the upper connector, attach the wires and fasten the terminal cover to the speaker unit with screws before attaching the disassembled bracket base Ⓐ.
  2. Use a flat-head screwdriver to loosen the terminal screws in the Euroblock plug, insert the wires into the terminal openings, and then securely fasten the screws.
    Pull on the wires to confirm they cannot be pulled out.
    NOTE
    Route the wires through the included terminal cover before inserting them into the connector.
    NOTE
    Use a flat-head screwdriver with a blade width of 3 mm or less.
    Mount the speaker to the pole before the Euroblock plug with connected wires is reinserted into the socket on the main unit.
  3. Attach the safety wire in a manner that allows confirming its ability to prevent the speaker from falling.
    WARNING
    • Use the included safety wire.
    • If the included safety wire is not long enough, procure a suitable safety wire that is long enough and strong enough for the speaker weight and installation conditions.
    • Attach the safety wire at a position higher than the speaker with no slack.

Attaching the mounting bracket and safety wire to a speaker

  1. Install bolts Ⓒ (M6 × 25 square neck bolts, washers, and nuts) included with mounting bracket Ⓐ.
    Use the washers (M6 for square neck bolts) removed during mounting bracket disassembly.


  2. Use the included screws Ⓓ to attach mounting bracket Ⓐ (with included M6 × 25 square neck bolts) to the speaker.
    Attach one bracket for model VXL1-8-WR or two brackets for models VXL1-16-WR and VXL1-24-WR.
    Refer to the figure below to determine the location for attaching mounting bracket Ⓐ and the safety wire.



Setting the speaker orientation (VXL1-24-WR, VXL1-16-WR only)

  1. Use a flat-head screwdriver to set the vertical coverage selector switch located on the back of the speaker.



    To expand the downward coverage area, set the switch to the [WIDE] position.



Mounting the speaker to a pole

  1. Install it to the second and third holes from the top of bracket base Ⓐ.
    Rotate bracket base Ⓐ toward the side so the base can be attached.
  2. Install the speaker using the flat washers, spring washers, and nuts obtained from disassembling the mounting bracket.


  3. After connecting the wires, reinsert the Euroblock plug back into the socket on the main unit.
    Fasten the terminal cover to the main unit with screws.



    NOTICE
    Implement appropriate measures to ensure the opening at the bottom of the terminal cover is waterproof.

Adjusting the speaker angle

  1. Adjust the horizontal swing angle and then tighten the bolts on the top and bottom of the bracket base.




HOME

  • HOME
  • Installing the speaker transformer (ST-L1a)

Installing the speaker transformer (ST-L1a)

CAUTION
Do not install the speaker transformer ST-L1a onto any speaker system other than the VXL1 Series.
NOTICE
  • A single unit of speaker transformer supports a single unit of VXL1 Series.
  • Implement appropriate measures to ensure the opening at the bottom of the terminal cover is waterproof.
NOTE
ST-L1a speaker transformer can be used outdoors by combining it with VXL1-WR [outdoor model] Series.

Installing the vertical coupling bracket onto the speaker

  1. Install the vertical coupling bracket onto the speaker using the included screws.
    NOTICE
    Be sure to use the vertical coupling bracket included in the product package.

Connecting the cables between the ST-L1a and the speaker unit

  1. Remove the Euroblock plug from the speaker and the ST-L1a.
  2. Use a flat-headed screwdriver to loosen the terminal screws of the Euroblock plug, insert the cables into the terminal openings, and then tighten the screws.
    Make sure the cables are secure and cannot be pulled out.
    NOTE
    When installing outdoors, run the cables through the included terminal cover before inserting them into the connector.
    NOTE
    Use a flat-headed screwdriver with a blade width of 3 mm or less.
  3. Connect the OUT connector of the ST-L1a and the connector of the speaker unit.

Installing the bracket and safety wire

  1. When installing the unit onto the wall using the included brackets, see "Installation with included brackets (excluding -WR [outdoor model])" for the installation procedure.
  2. When installing the unit onto the wall using the WMB-L1, see "Installation with wall mounting bracket (WMB-L1)(excluding -WR [outdoor model])" for the installation procedure.

Connecting the cables between the ST-L1a and the amplifier

  1. Connect the cables from the amplifier to the IN connector of the ST-L1a.

Setting the type and input wattage of the speaker

CAUTION
When operating the Speaker Selector, make sure the power amplifier is turned off.
NOTICE
Make sure that the total input wattage of speaker connected does not exceed the output of the power amplifier. Wrong setting will cause a malfunction in the speaker or the power amplifier.
  1. Select the speaker to use, by turning the Speaker Selector on the side of the ST-L1a with a flat-headed screwdriver.
  2. Similarly, select a tap to the transmission system (100-line (100 V)/70-line (70 V)) and the input wattage, by turning the Tap Selector with a flat-headed screwdriver.
NOTE
Do not connect to the 100 V power supply for home use

For details of connection at high impedance, see the explanation of the connection at high impedance at the following URL.
Yamaha Pro Audio site "Better Sound for Commercial Installations":
http://www.yamahaproaudio.com/global/en/training_support/better_sound/

NOTE
As necessary, affix a selector cover to the unit.

HOME

  • HOME
  • Installing the port cover (excluding -WR [outdoor model])

Installing the port cover (excluding -WR [outdoor model])

If you require waterproofing equivalent to that of the IP35, install the port cover that is included with this product. -WR (outdoor model) is IP55 compliant when used as is.

CAUTION
Use gloves or other protective wear when removing the grille, in order to avoid cutting your hands on the grille edges.
  1. Remove the four screws on the top and bottom sides of the speaker, and remove the top and bottom panels.
  2. Use caution not to scratch the grille, and slowly remove it from the speaker.
  3. Remove the four screws from the bass reflex port.
    There are two bass reflex ports (top and bottom) on the VXL1-24/VXL1-16.
  4. Align the port cover and fasten it in place using the screws that you removed.

    (For VXL1-8) Insert the port block into the bass reflex port, and then align the port cover and fasten it in place using the screws that you removed.
    NOTE
    Insert the port block so that it fits into the port.
  5. Put the grille back on the speaker.
    When doing this, align the edges of the speaker with the position of the grille to fit the grille in place.
  6. Fasten the top and bottom panels in place using the screws that you removed.

HOME

  • HOME
  • Painting

Painting

When painting the VXL1 and the speaker transformer, we recommend using acrylic lacquer paint.

WARNING
Do not disassemble or modify this device (painting and installing the port cover excepted).
Doing so may cause electrical shock, fire, injury or malfunction.
CAUTION
  • Work in an area that has adequate ventilation.
  • Be careful when removing the grille to avoid injury.
NOTICE
  • Painting procedures often require the use of volatile solvents that can cause fire. Follow all necessary safety precautions to avoid any risk of a fire or accident.
  • Damage caused by painting the speaker is not covered by the warranty.
NOTE
The speaker transformer ST-L1a can be painted in the same way.

Painting the grille

  1. Remove the four screws from the top and bottom of the speaker, and remove the top and the bottom plate.
  2. Remove the grille from the speaker, taking care not to scratch it.
    CAUTION
    When removing the grille, wear gloves so as not to cut your hands on the grille edge.
  3. Remove the emblem on the front of the grille.
    The emblem is attached by adhesive tape.
  4. Before painting, remove any dust or dirt from the grille.
    Do not sand the enclosure.
  5. Use spray paint to paint the grille.

    NOTE
    Make sure the holes in the grille do not become clogged with paint. If the holes become clogged with paint, sound quality may be affected.
  6. When the paint is completely dry, attach the emblem to the grille.

Painting the speaker enclosure

  1. Before painting, remove any dust or dirt from the enclosure.
    Do not sand the enclosure.
  2. Use spray paint to paint the enclosure.
    Cover the speaker unit, baffle, and connectors using masking materials to avoid paint contact.
  3. Allow the paint to dry completely.
  4. After painting the speaker enclosure, top plate, and bottom plate, reattach the grille to the speaker.
    At this time, fit them with the speaker and grille ends in alignment.
  5. Fasten the top and the bottom plate with the removed screws.

HOME

Error

Print

  • foo
  • bar