Summary

The page that provides visualization and monitoring of various system information and status information is called the "dashboard".

When a parameter being monitored exceeds the threshold value, it is shown in a warning field, helping you to determine the cause of a problem or to perform troubleshooting.

Each window shown in the dashboard is called a "gadget".

A gadget that you want to monitor can be placed anywhere you like.

Information for each gadget is automatically updated at regular intervals.

If the stack configuration is enabled, the stack switch button will be displayed at upper left.

Select a stack ID to display the stack information selected on the following gadgets.

This can only be selected for stacks with active status.

The main switch will be selected on the initial screen.

Information for selected stacks for separated gadgets will be shown per gadget at the next update timing.

From the "Gadget" buttons () in the upper right, select the gadgets that you want to be displayed.

A maximum of 32 warnings are shown, from newest to oldest.

Each of the displayed gadgets monitors the situation, and when an abnormal situation or a high load is detected, the "Warning" button () flashes and a list of warnings appears under the "Warning" button.

The list of warnings shows the contents of the currently detected warnings in order of recentness.

The bar of the gadget that is the object of the warning is also shown with a flashing "Warning" button.

When the following conditions are satisfied, the warning will stop being displayed (the conditions differ depending on the detected content).

If all warning indications disappear, the "Warning" button stops flashing, and the warning list disappears.

You can press the "Warning" button to open or close the warning list.

You cannot open the warning list and the warning history list at the same time.

The warning history is shown in order of newness, for a maximum of 64 items.

The warning history is shown in bold, but warnings that were cleared by the "Clear" button in the warning list are shown in thin characters.

If there are unconfirmed warning history entries that have not been cleared, the number of such entries is displayed at the lower right of the "History" button (). This number corresponds to the count of warning history entries displayed in bold ().
If this number is displayed, check the contents of the warnings that have occurred in the warning history list.

When you press the "OK" button () of each item in the warning history list, it changes to thin characters as a confirmed history item, and the "OK" button disappears.

In the warning history list, pressing the "All confirmed" button () changes all history entries to a confirmed state.

In the warning history list, pressing the "All deleted" button () deletes all history.

You can press the "History" button to open or close the warning history list.

You cannot open the warning list and the warning history list at the same time.

Press the "Gadget" button () in the upper right, select the gadget that you want to use from the gadget list, and then press the "Apply" button.

Gadgets are always added to the far upper left of the dashboard.

Press the "Gadget" button () in the upper right, clear a selection from the gadget list, and then press the "Apply" button.

You can also delete a gadget by pressing the "Close" button () in the upper right of each gadget.

When you place the mouse over each gadget, the mouse pointer changes to a move symbol, allowing you to drag the gadget to a desired position.

Candidates for the gadget’s movement destination are shown in gray.

The interface information gadget cannot be moved.

A "Separate" button () is displayed at the upper right of each gadget.

If you press the "Separate" button, that gadget alone is shown in a different window.

At this time, the corresponding gadget in the dashboard is indicated as "In separate window".

If a gadget is separated, the following occurs.

Separated gadgets can also be displayed by specifying a URL directly in the browser.

When you press the minimize icon at the upper left of each gadget (), the icon changes to a horizontal orientation (), and the gadget is displayed in a minimized state.

When you press the minimize icon again, the icon returns to its original downward orientation (), and the gadget returns to its original size.

When you add, delete, or move a gadget, or when you minimize and restore it, the position data of the gadget is saved.

This information is also saved when the power is turned off and on again.

This data is initialized if you return the device to its factory-set state.

If a general user logs in, the gadget position information is not saved.

All gadgets are automatically updated at regular intervals.

The update interval differs depending on the gadget.

When an abnormal condition or a high load is detected by a gadget, a flashing "Warning" button () is displayed beside the minimize icon of that gadget.

The following states will initiate this warning.